3Dponics Drip Hydroponics System

Here you'll find every 3D-printable part you'll either need or want to build your 3Dponics drip hydroponics system, including originals like the drip nozzle, silencer and conduit!
24 Pins123 Followers
Sprinkler Head (3/8 Inch) | Distributes water evenly over plant leaves to enhance plant health and growth. Can be installed above each bottle (underneath drip nozzle). Fits 3/8 inch tubing. #3Dponics

Sprinkler Head (3/8 Inch) | Distributes water evenly over plant leaves to enhance plant health and growth. Can be installed above each bottle (underneath drip nozzle). Fits 3/8 inch tubing. #3Dponics

Silencer | Reduces the noise produced by the system when the pump is operating so that you can have a system in your living room or kitchen. #3Dponics

Silencer | Reduces the noise produced by the system when the pump is operating so that you can have a system in your living room or kitchen. #3Dponics

Pump Connector | Allows you to connect up to 10 systems to one water pump. It has been modified to print well without supports or raft. #3Dponics

Pump Connector | Allows you to connect up to 10 systems to one water pump. It has been modified to print well without supports or raft. #3Dponics

Drip Nozzle (4 Hole, 3/4 Inch) | Screws on to bottle like a bottle cap and ensures that the water drips at a controlled rate. To attach to the next bottle, thread zip ties through the four holes. Fits 3/4-inch tubing. #3Dponics

Drip Nozzle (4 Hole, 3/4 Inch) | Screws on to bottle like a bottle cap and ensures that the water drips at a controlled rate. To attach to the next bottle, thread zip ties through the four holes. Fits 3/4-inch tubing. #3Dponics

Used in combination with the Inner and Outer Clips. Adjustable, allowing you to choose how much distance there is between bottles. Eliminates the need for zip ties.

Used in combination with the Inner and Outer Clips. Adjustable, allowing you to choose how much distance there is between bottles. Eliminates the need for zip ties.

Outer Clip | Used in combination with the Inner Clip and Spacer. Allows you to fasten the bottles together and adjust the distance between them. A great alternative to zip ties. #3Dponics

Outer Clip | Used in combination with the Inner Clip and Spacer. Allows you to fasten the bottles together and adjust the distance between them. A great alternative to zip ties. #3Dponics

Inner Clip | Used in combination with Outer Clip and Spacer to fasten the bottles together. Allows you to adjust the distance between the bottles. A great alternative to zip ties. #3Dponics

Inner Clip | Used in combination with Outer Clip and Spacer to fasten the bottles together. Allows you to adjust the distance between the bottles. A great alternative to zip ties. #3Dponics

Y-Splitter (Version 2) | New version of Y-Splitter, upgraded to print more easily. Allows you to split your tubing to power multiple 3Dponics systems using just one air bubbler. Can be used with the 3Dponics Drip System or the Non-Circulating System. #3Dponics

Planter (Square) - Non-Circulating Hydroponics System on makexyz

Y-Splitter (Version 1) | Allows you to split your tubing to power multiple 3Dponics systems using just one air bubbler. Can be used with the 3Dponics Drip System or the Non-Circulating System. #3Dponics

Y-Splitter (Version 1) | Allows you to split your tubing to power multiple 3Dponics systems using just one air bubbler. Can be used with the 3Dponics Drip System or the Non-Circulating System. #3Dponics

Venturi | An improved version of the original conduit. It’s smaller and therefore takes less time and material to print. It’s also more efficient and can send more water to the top of the 3Dponics system.  If you have a dual outlet pump (e.g. HagenMarina 200), you can power two or more 3Dponics systems with one air pump. #3Dponics

Venturi | An improved version of the original conduit. It’s smaller and therefore takes less time and material to print. It’s also more efficient and can send more water to the top of the 3Dponics system. If you have a dual outlet pump (e.g. HagenMarina 200), you can power two or more 3Dponics systems with one air pump. #3Dponics

Support Rod (Square) | Feed your rubber tubing through the hollow rod to ensure that the water or nutrient solution flows smoothly through your system. It also ensures that the conduit or venturi is positioned vertically in the nutrient solution so that it can suck up the water efficiently. #3Dponics

Support Rod (Square) | Feed your rubber tubing through the hollow rod to ensure that the water or nutrient solution flows smoothly through your system. It also ensures that the conduit or venturi is positioned vertically in the nutrient solution so that it can suck up the water efficiently. #3Dponics

Support Rod (Round) | Modular and easy to assemble. Feed your rubber tubing through the hollow rod to ensure that the water or nutrient solution flows smoothly and efficiently through your system. #3Dponics

Support Rod (Round) | Modular and easy to assemble. Feed your rubber tubing through the hollow rod to ensure that the water or nutrient solution flows smoothly and efficiently through your system. #3Dponics

Sprinkler Head (3/4 Inch) - Distributes water evenly over plant leaves to enhance plant health and growth. Can be installed above each bottle (underneath drip nozzle). Fits 3/4 inch tubing. #3Dponics

Sprinkler Head Inch) - Distributes water evenly over plant leaves to enhance plant health and growth. Can be installed above each bottle (underneath drip nozzle).

Grow Media Basket Version 2 | Holds the grow media and protects the plant roots from damage. Version 2 is great for clay, coco or perlite grow media. Fits inside 2-L bottles. #3Dponics

The Grow Media Basket holds the grow medium and protects the plant roots from damage. Version 2 is great for clay, coco or perlite grow medi.

Pinterest
Search